pic18f452 pinout

Introduction to PIC18F452 Microcontroller 2

[otw_is sidebar=otw-sidebar-1]PIC18F452 Microcontroller,datasheet of PIC18F452 Microcontroller,basic circuit of PIC18F452 MicrocontrollerIn this post I will discuss about the Introduction to PIC18F452 Microcontroller. In the previous posts I have discussed about the Pic 16f676 Microcontroller Voltmeter and also have discussed important sensors and actuators in Microcontroller . This post will be oriented around the pic185452 and its simulation in Proteus.
After reading this post the reader will be able to learn about the basics of the PIC18F452 Microcontroller, working of the PIC18F452 Microcontroller, the principle of the PIC18F452 Microcontroller, circuit for PIC18F452 Microcontroller, interfacing of the pic microcontroller development board with PIC18F452 Microcontroller in Proteus. So sit back, keep reading and enjoy learning.

Introduction to PIC18F452 Microcontroller

 

Pic 18f452  Features
    • pic18f452 has 2 PWM 10-Bit
    • pic18f452 has  Self-Programming
    • pic18f452 has  40 MHz Max. Speed
    • pic18f452 has  ICD
    • pic18f452 has PSP
pic18f452 features

Pic18f452 Pinout

Here is the Following figure shows the Pic18f452 Pinout this is very easy and simple  pic18f452 pin configuration/pic18f452 pin diagram.There are 5 ports in pic18f452,4 timers,1 rx,tx,builtin 5 adc,and 3 ccp modules.and also spi,i2c module in it,it can easy program from icsp header,

.

pic18f452 pinout,pic18f452 pin configuration,pic18f452 pin diagram
PIC18F452 Microcontroller Circuit Diagram
here is the basic circuit diagram of pic 18f452.it is for beginners
pic18f452 basic circuit,PIC18F452 Microcontroller Circuit Diagram

Pickit 3 connection for pic18f452 microcontrollerhere

here is the simple and easy Pickit 3 connection for pic18f452 microcontroller it is also called pickit3 icsp header for programming
pic18f452 icsp pickit3,pickit3 pinout,pickit3 pin configuration
PicKit 3 Pin Number 1 

 

The PicKit 3 Pin Number 1 is called MCLR/Vpp =Connected to Master clear external reset pin of PIC to reset the MCU before programming

PicKit 3 Pin Number 2

The PicKit 3 Pin Number 2 is called VDD (Target) Target voltage of PIC, 5V or 3.3V
[otw_is sidebar=otw-sidebar-2]
 

PicKit 3 Pin Number 3

The PicKit 3 Pin Number 3 is called Ground Ground pin of the system

PicKit 3 Pin Number 4

The PicKit 3 Pin Number 4 is called PGD/ICSPDATProgram Data(PDG) is connected to the In Circuit Serial Programming (ICSP) data pin

PicKit 3 Pin Number 5

The PicKit 3 Pin Number 5 is called PGC/ICSPCLKProgram Clock (PGC) is connected to In Circuit Serial Programming (ICSP) clock pin

PicKit 3 Pin Number 6

The PicKit 3 Pin Number 6 is called No connection This pin is reserved for future application

 

 

microcontroller for beginners

 

That is all for now (Introduction to PIC18F452 Microcontroller) I hope this post would be helpful for you. In the next post I will come up with more interesting applications and simulations of the Proteus. Till then stay connected, keep reading and enjoy learning.

2 Comments

  1. What’s up, yup this paragraph is really good and I
    have learned lot of things from it on the topic of blogging.
    thanks.

Trackbacks and Pingbacks

  1. […] based delay in STM32 is simply just like creating delay for any other micrcontroller which support C/C++. The only difference that you may see in the code is the __IO macro which will […]

Leave a Reply

Your email address will not be published. Required fields are marked *